Build a 7-Foot Scrap Workbench in About 90 Minutes
This is the workbench I built from scrap: a 74-1/2 in. by 24 in. frame, a 78 in. by about 26 in. plywood top, and an old quick-release vise bolted to one end. It took me about an hour and 45 minutes with the vise. It's a shed bench, not furniture, so don't sweat the small stuff. As I like to say, if it's off by an eighth of an inch, so what?
Watch the full build on YouTube
Materials
- Legs: pressure-treated 4x4 lumber, enough for four 33 in. legs. Mine came from 96 in. pieces, two legs from each. Use dry wood (see tips).
- Frame: 2x4s, lightly planed clean if they need it.
- Top: one piece of 3/4 in. prefinished plywood.
- Screw blocks: strips about 3/4 by 7/8 in. I used hardwood scrap; any hardwood works.
- Screws: 3 in. self-tapping screws for the frame and legs; 1-1/2 in. screws for the blocks; 1-1/4 in. screws up through the blocks into the top.
- Vise: an old quick-release vise (mine is a Columbia) and bolts large enough to need pre-drilled holes.
- Glue: wood glue. Standard Titebond is fine; use Titebond III if the bench will see moisture.
- Extras: a magnetic strip and two screws to mount it.
Cut list
The finished bench stands about 34 in. high: 33 in. legs plus the 3/4 in. top.
| Part | Qty | Size | Notes |
|---|---|---|---|
| Legs | 4 | 4x4, 33 in. long | Trim off any checked or knotty end first; use a stop block so all four match |
| Long frame pieces | 2 | 2x4, 74-1/2 in. | |
| End cross pieces | 2 | 2x4, 24 in. | Sets the bench width at 24 in. |
| Center brace | 1 | 2x4, 21-1/4 in. | Sits at the halfway point, 37-1/4 in. from the end |
| Top | 1 | 3/4 in. plywood, 78 in. by about 26 in. | About 1-5/8 in. overhang at each end; flush with the front |
| Screw blocks | several | about 3/4 by 7/8 in., lengths vary | Four long and several short; lengths in the ballpark |
Tools
Chop saw with a stop block, band saw, planer, drill press, impact driver and drill, router, track saw, table saw, rasp, clamps, a square and a block plane. A scroll saw helps for cleanup but isn't required.
Build steps
- Cut the legs. Set the chop saw stop at 33 in. Trim any checked or knotty end first, then cut four legs to the same length.
- Cut the frame pieces. Plane the 2x4s lightly if they need cleaning up. Cut two long pieces at 74-1/2 in. and two cross pieces at 24 in.
- Notch the tops of the legs. On the band saw, cut a notch in the top of each leg so a long piece and a cross piece can sit in it, so the weight of the top goes straight down the leg. Size the notch to your lumber and test-fit. Use a clamp as a depth stop. Wait for the blade to stop before pulling stock out, and support the piece so it can't fall.
- Build the two end frames. Glue each joint and drive 3 in. self-tapping screws, staggered, three per joint. Check each frame for square.
- Add the long pieces. Glue and clamp them into the notches, with three screws per joint to keep the bench from racking.
- Add the center brace. Cut a 2x4 at 21-1/4 in. and screw it in from the sides at the halfway point, 37-1/4 in. from the end. Keep the screws slightly off the edge so you don't hit the ones already there.
- Mount the vise. Pick the end that suits where you stand and work. Keep the vise top flush with the bench top so the face of the front 2x4 becomes the back of the vise. Mark where the vise top sits, notch the front 2x4 to let it in, pre-drill the bolt holes and bolt it on. If you want the vise raised, 3/4 in. spacers between the vise and the underside of the top are an easy upgrade.
- Cut the top. Cut the plywood to 78 in. long and about 26 in. wide with a track saw and table saw. Leave about 1-5/8 in. overhang at each end and keep the front flush with the frame.
- Route the relief for the vise. The vise sticks up under the top, so cut a shallow slot, about 5/8 in. deep, freehand with a router against a straight edge. Take several passes and test the fit against your vise before attaching the top.
- Make the screw blocks. Rip hardwood strips to about 3/4 by 7/8 in. and cut them to lengths in the ballpark. Pre-drill the screw holes on the drill press, about three holes on each side of each block.
- Glue the blocks to the frame. Glue and screw them to the inside of the frame, just shy of the top edge, with 1-1/2 in. screws driven straight in (not pocket screws). Don't glue them to the top, so the top can come off if it ever needs replacing.
- Attach the top. Lay the top upside down, set the frame on it, and line up the front and ends. Drive 1-1/4 in. screws up through the blocks into the top, one at each end first, then around the edge. The blocks are about 7/8 in. thick and the top is 3/4 in., so the screws won't poke through.
- Finish up. Screw a magnetic strip on the end, knock the sharp edges off with a block plane, and you're done.
Tips and notes
- Use dry pressure-treated wood. Wet PT lumber warps as it dries, and the moisture can carry into your tools and other wood. Let it dry before you build.
- Pre-drill where it matters. On a shed bench like this I drive the 3 in. self-tapping screws without pre-drilling. I do pre-drill the big vise bolts and the screw holes in the blocks. For furniture-grade work, or anywhere near the end of a board, pre-drill.
- Glue is stronger than the wood. Use glue on the joints and the screw blocks, not only screws.
- Plan the vise end around you. Put the vise where it suits your dominant hand and the layout of your door and walls.
- Wait for the saw to stop before you lift the cut piece.
Upgrades
- A shelf under the bench, built from a square frame and prefinished hardwood flooring.
- 3/4 in. spacers between the vise and the underside of the top.
Want to see it built? Watch the full 1 hour 42 minute build video on YouTube.

